8216 uTrust Touch Secure Keypad Reader

This document details the Physical Access Control Reader uTrust TS Contact KEYPAD READER and its basic user instruction and installation procedures.

Reader

Functionality

8216 is a physical access control smart card reader (accessory equipment) that can read the following credentials:

• Contactless HF (13.56MHz) conforming with ISO 14443 A & B, ISO15693

• Contactless LF (125KHz) credentials of type FSK, ASK, PSK

• Contact Smartcards – conforming to ISO-7816 in the ID-1 formfactor

• Keypad interface - can be used stand-alone or, for high secure applications, it adds a second level of authentication with a user PIN

• User-feedback interfaces on the reader include RGB LED’s and Buzzer

 The reader can be interfaced with an access control panel equipped with a Wiegand or an RS-485 half-duplex interface

Reader Parts

a. Front/Top Casing

Open

b. Back View without Backplate

Open

c. Backplate

d. Rear View with Backplate

Product Details

Specifications

Product Label

Product Certification IDs

• FCC Certification ID - MBPTSKPSC-00

• IC Certification ID - 7485A-TSKPSCR0

Installation Details

Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction.

Parts List

• TS Contact Keypad reader -1

• Screws (A #6-18X1.5" SS) - 4Nos – Back Plate mounting screws for Wall

• Snake Eye Screw (SMF #6-32X5/16” SS) – 1 No- Top casing mounting security screw

• Screws (SMF #6-32x3/8" SS) - 3 No’s - 1 casing to back plate mounting screw and 2 Junction Box mounting screws

• Nylon anchor plug -4 Nos

• 6 pin phoenix plug (Phoenix connector version only) – 2 Nos

• Back Plate

Recommended Infrastructure

All cabling and wiring shall be UL Listed and/or UL Recognized.

Connector Information

Pinout diagram

Mounting the Reader

Location of mounting holes on wall

Reader Installation Steps

1. Make the required holes on the wall as per the backplate drawing above.

2. The reader is to be mounted at a height less than 2 meters from the floor for MS1 compliance as per IEC 62368-1

3. Insert the nylon screw plugs into the wall.

4. Connect the wires as per the Table 1 above.

5. Secure the backplate onto the wall using the Screws (A #6-18X1.5"SS )

6. Hook the reader onto the backplate

7. Secure the reader and backplate by the Snake Eye Screw (SMF #6-32X5/16"SS)

Power up and Testing

1. Turn power on
   The LED blinks 3 times green with a long beep, then turns red.

2. Present a card
   Contactless card: The LED blinks green, and a short Beep is heard
   Contact card: The LED blinks Green and a short Beep is heard

3. Press Key
   Buzzer tone and backlight LED blinks.
   
   

Certifications

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

Information to the user
Changes or modifications not expressly approved by Identiv could void the user's authority to operate the equipment.

IC

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device

CE

Identiv hereby declares that the uTrust TS Contact Keypad Reader Model 8216 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

UL 294 and UL 1076

• Communication via Wiegand and OSDP was evaluated by UL and serves as the interface between the reader and panel

• When the reader is powered by a supply other than Identiv Mx series controller, the power supply should be a UL 294 and 1076 listed , class 2 supply

• For UL 1076, the reader was assessed for the acknowledgment signal annunciation while interfacing to the listed Identiv Mx series control unit via Wiegand only

UL 294 Access Control Performance Levels