/
80X0 uTrust Touch Secure Mullion Reader

80X0 uTrust Touch Secure Mullion Reader

Search

 

Introduction


This document details the Physical Access Control Reader TouchSecure® and its basic operational and installation procedures. It covers the details of the Mullion form-factor reader.
Model: Connectivity/Standard MUL.

  • The reader comes in two variants for interfacing with the control panel:

    • Pigtail - 8000ABP, 8010ABP

    • Phoenix connectors - 8000ABT, 8010ABT, 8030ABC

    • P - refers to Pigtail, T - refers to Terminal (Phoenix header)

  • The reader comes in three variants in functionality

    • Standard HF Only - 8000ABP, 8000ABT

    • Standard HF LF - 8010ABP, 8010ABT

    • Connectivity HF LF - 8030ABC

    • P - refers to Pigtail, T - refers to Terminal (Phoenix header), C - refers to connectivity

    • In connectivity, Only Terminal version is available

Reader

Functionality


TouchSecure reader is a physical access control smart card reader that can read HF and LF contactless credentials, conforming to the following standards: ISO 14443 A & B, ISO15693. The reader can interface with an access control system equipped with a Wiegand or RS-485 serial interface.

Reader parts


The reader consists of the following main parts:

a. Top Casing

 

b. Touch Screen Reader with Bottom Casing

Reader variants


Product Details


Model Name

Connectivity/Standard MULLION.

Device Type

RFID reader, 13.56MHz (HF) / 125 KHz (LF).
Physical Access control Reader (accessory equipment).

Type of equipment

Potted reader.
Suitable for Indoor use - 8030ABC and
Outdoor use - 8000ABP, 8000ABT, 8010ABP, 8010ABT.

Interface Type

Pigtail Cable (11 Core + Drain) or Phoenix connectors and RJ45.

Voltage Rating (8030ABC)

6-16VDC or 48VDC on RJ45 Connector.

Voltage Rating (All other models)

5-16VDC.

Communication protocol

Wiegand, RS-485 (2wire - Half Duplex), 10BaseT ETH.

* Communication via Wiegand and OSDP was evaluated by UL and serves as the interface between the reader and panel, Communication via Ethernet was not evaluated by UL.

Reader Specifications


Model

Operating Voltage

Current rating

Operating temp

Model

Operating Voltage

Current rating

Operating temp

8000ABP
8000ABT
STANDARD HF ONLY

5 - 16VDC

Refer graph in section

 

 

 

-35 to +65 Deg C

8010ABP
8010ABT
HF LF

5 - 16VDC

8030ABC
HF LF
CONNECTIVITY

6 - 16VDC

 

 

0 to +49 Deg C

PoE @ 48VDC

*PoE sourcing equipment shall be UL 294 or UL 294B Listed with Class 2 output.

  • When the readers use PoE as a power source, the power input wiring from the control unit (i.e. Red and Black for 8030) shall be disconnected.

  • The maximum length of the Ethernet cable when using PoE as the power source in UL installations is limited to 30 meters (98.5 feet).

Standby Power is not provided by the Card Readers. The Standby Power Level is dependent on the external power source connected to the Card Reader.

  • All wiring or cables to the Card Readers shall be the shielded type.

  • Only UL Listed PoE sourcing equipment, or UL Listed power-limited power supply, or power-limited output from UL Listed control panel shall be used for the Power Over Ethernet feature. Cat 5e cabling is the minimum performance category recommended. These Card Readers when using PoE feature are not intended for outside wiring as covered by Article 800 of the US National Electrical Code, NFPA 70.

Rated current at different operating voltages

Rated current for Model 8000


Voltage (V)